3/28/2011

Rheem Outdoor Liquid Propane Tankless Water Heater for 2-3 Bathroom Homes - RTG-66XP Review

Rheem Outdoor Liquid Propane Tankless Water Heater for 2-3 Bathroom Homes - RTG-66XP
Average Reviews:

(More customer reviews)
We have a 2200 sq foot home which had the hot water tank 40 feet from the kitchen and 70 feet from the master bath so it always took a full minute and many wasted gallons of water to get something hot. With the floor plan relocating an indoor tank to the center of the house was not ideal though the indoor tankless would have been an option but I did not want to deal with the work of the air intake and chimney install.
The information on the Rheem outdoor tankless was mixed and stated that is was good to -30 and yet elsewhere I saw it listed at 30. That said, the -30 was on their website so we decided to go with it. Upon receiving it and the additional grey pipe cover which was not sold here at Amazon. I did find and buy it at Wholesale America and it is definitely something you'll need to make this a clean install.
SKU: RTG20169XG Weight: 9 lbs Rheem RTG20169XG Grey Pipe Covers for the RTG66-X $64.29
After installing my pipes, gas and electric I insulated this cover with hard Styrofoam and of course also ran a heat tape on the pipes coming out and going in. In mounting this tank to the house, I stayed low and used a 2.5" hole saw to make 5 holes through to the crawl space which will allow more of that warmth to access the now insulated pipe cover.
It is still early November in Kansas and if any problems develop during the colder parts of winter, I will update this posting.
As far as the tank and how it works, it is wonderful! We are using propane from a 1000 gallon tank and as with most of these installs, the tank has a first stage regulator and then at the house is a second stage. We have a gas furnace, dryer, stove and now this higher Btu hot water tank so I was naturally concerned that I might need to install a tee and place a second second stage regulator at the house and then run a dedicated line to the new water heater. I opted to try and tap into the lines using the appropriate flex pipe for high volume and it worked out just fine with only the one regulator. We tested this by running the furnace, dryer, oven and burners while running hot water. By holding a meat thermometer in the stream of hot water while the tank thermostat was set at 120F, I had a steady reading of 119 and when set at 130 I had 129 which means one or the other of these is off a wee little bit but the tank produces the hot water as it should! How cool is that?
With regard to the remote thermostat that you'll get with this... it only goes up to 120F until you bypass that if you want to go to 125, 130, 135 or 140. The instruction sheet that came with our tank was confusing and instructed me to open the tank cover and switch a dip switch and push a button and watch for a flashing light etc. Please don't waste your time!! I called their 800 number and talked to somebody in 'trouble shooting' and she instructed me to simply go to the thermostat and with it set at 120, hold the 'temp up' key until 140 pops up. Then I think she said to hold both up and down keys and that would lock me into the higher temp settings. You can then adjust in 5 degree increments and we chose 130 because we have a dishwasher and no little ones in the house.
The unit works well delivering endless supplies of hot water and is very quiet not that it matters outside!

Click Here to see more reviews about: Rheem Outdoor Liquid Propane Tankless Water Heater for 2-3 Bathroom Homes - RTG-66XP

Includes Outdoor Liquid Propane Tankless Water Heater for 2-3 Bathroom Homes - RTG-66XP

Buy NowGet 48% OFF

Buy cheap Rheem Outdoor Liquid Propane Tankless Water Heater for 2-3 Bathroom Homes - RTG-66XP now.

3/27/2011

11-1/2" Water Heater Review

11-1/2 Water Heater
Average Reviews:

(More customer reviews)
Love the heater, it heats my 100 gallon tank turning my pressure washer into a hot water unit!!!

Click Here to see more reviews about: 11-1/2" Water Heater

When the weather gets cold keep your hands warm! Portable immersion type water heater, 1150 W, 120 V. Use 5-1/2" max depth for wet saws. Use 11-1/2" max depth for buckets.

Buy Now

Buy cheap 11-1/2" Water Heater now.

3/26/2011

Farm Innovators Submergible Bucket Heater with Attached Guard Model W-449, 1,000-Watt Review

Farm Innovators Submergible Bucket Heater with Attached Guard Model W-449, 1,000-Watt
Average Reviews:

(More customer reviews)
We use this as an auxiliary heater to get our hot tub up to temperature more quickly.
Works great - cuts heating time by 60%. I also use it my shop to get warm water - rather than the expense of installing a hot water heater.
Wish the cord was a bit longer, but the guard around the element keeps it off the bottom of the tub
and the 1000W power makes it easy to plug into any electrical outlet.
This is a well made product - lots of uses around the house.

Click Here to see more reviews about: Farm Innovators Submergible Bucket Heater with Attached Guard Model W-449, 1,000-Watt

This submergible bucket heater is designed to heat 5 gallons of water up to 110°F. The built-in thermostatic control maintains water temperature between 85°F and 110°F. Safe in plastic buckets. One year limited warranty.

Buy NowGet 42% OFF

Buy cheap Farm Innovators Submergible Bucket Heater with Attached Guard Model W-449, 1,000-Watt now.

3/25/2011

Intermatic WH21 Electric Water Heater Timer Review

Intermatic WH21 Electric Water Heater Timer
Average Reviews:

(More customer reviews)
This product is easy to install if you know what you are doing.
You should have some background in electrical ampacity and wiring basics.
I did have to purchase an additional pigtail.(flex tubing with 3 #10 color coded wires, and 1/2 connectors on each end about 5 feet total length)
The heater had the wiring flex tubing direct from the wall to the top of the heater. The additional material was about 10.75 at the local hardware store.
I unhooked the wiring from the heater and wired it to the timer, then wired the new pigtail to where I had disconnected the original wires.
The timer has knockouts on the bottom for either 1/2 or 3/4 inch connectors so if it will accomodate either one. You most likely will have 1/2" connections.
Make sure you turn off the breaker before you start.
The entire process took about an hour total.
The instructions that come with the timer aren't that great, so if you don't know what you are doing, it won't help much.
The timer comes with 3 sets of on/off clips so you can time it on and off 3 times.
We set it at on at 5 am, off at 8 am, then on at 8 pm off at 10 pm.
So the timer is on 5 hours a day and off 19.
We figgure we will save around 25 dollars a month off the electric bill.
So... it will take at least 2 months to pay for the timer and other materials we bought. If you pay someone to install it, it will take much longer to pay for itself.
So far, it is working properly and so I am satisfied.

Click Here to see more reviews about: Intermatic WH21 Electric Water Heater Timer

25A, Water Heater Timer, Electric, External Switch, On/Off Indicator Light, Single Pole, Single Throw, 6,250W, 250V.

Buy NowGet 50% OFF

Buy cheap Intermatic WH21 Electric Water Heater Timer now.

3/24/2011

Bosch AE125 PowerStar 4 GPM Indoor Electric Tankless Water Heater, White Review

Bosch AE125 PowerStar 4 GPM Indoor Electric Tankless Water Heater, White
Average Reviews:

(More customer reviews)
I purchased the Bosch AE125 Electric Tankless Water Heater 4 months ago and have regretted it. Several considerations should be taken.
First the unit is not an analogue to a conventional tank-type water heater. It delivers hot water based upon a system that measures the incoming water temperature and flow rate and then "calculates" the number of elements (it actually has 6) that it turns on to provide an outflow temperature based on the setting of the temperature control. This system is not satisfactory for a water supply which varies in pressure, SUCH AS A WELL, as the unit itself provides substantial resistance to flow and thus the flow rate through the unit varies and thus the temperature of the outgoing water. This causes the delivered water to vary widely in temperature, from VERY HOT to VERY COLD. The unit would be improved if it was "smart enough" to not only measure incoming temp, but, also, outgoing temperature and flow rate and maintain the outgoing temp at a constant level.
Second: The unit has a flow sensor, which will shut the heaters off at low flow, so, therefore, if you wish to have a small amount of hot water flowing into your sink for shaving purposes, the water will not be heated at all. This "Feature" also has considerable influence on the use of "low flow" faucets.
Third: If you have a home which is heated by electricity and you install this unit, be aware that it consumes 120 AMPS at maximum heat rate. In my case, my electric heat consumes 120 Amps, also; my home has a 200AMP panel. Do the math, turn on the heat to warm the house and then take a bath, and suddenly the entire house is plunged into darkness. I have decided that I must sense when the water heater is turned on and prevent the central heat from coming on. This should be doable, and since the unit only runs when hot water is required, should disable the central heat only for short periods. HOWEVER, this is a feature that should be provided by Bosch and/or their literature should make clear to the potential purchaser that this is a problem with the electric heater.
Fourth: The unit apparently switches one or more of its six elements on or off as it attempts to heat the water. There does not appear to be any partially on for any of the elements. This leads to the problem of "stepped" heating of the water. And because the unit measures flow in and calculates the outgoing rate, if the water is mildly too hot or too cold, simply changing the mix at the faucet does not necessarily result in mild changes in temperature, a tiny change at the faucet can cause one or all of the elements to switch off resulting in a dramatic change at the faucet. AGAIN an argument for sensing the outgoing temperature and maintaining it by modulating the elements for a smoother temperature curve.
I would rate this unit as unsatisfactory for any home with a well, and only marginally acceptable for any home with electric heat (but only if modified as I indicated above).
Had I known then, what I know now, I would have saved myself a lot of money and frustration by purchasing a conventional tank-type water heater.

Click Here to see more reviews about: Bosch AE125 PowerStar 4 GPM Indoor Electric Tankless Water Heater, White



Buy NowGet 12% OFF

Buy cheap Bosch AE125 PowerStar 4 GPM Indoor Electric Tankless Water Heater, White now.

3/23/2011

InSinkErator SST-FLTR 2/3-Gallon Stainless Tank and Filtration System Review

InSinkErator SST-FLTR 2/3-Gallon Stainless Tank and Filtration System
Average Reviews:

(More customer reviews)
(EDIT 01/27/2011) My initial review below was written based on an old design that had some quality issues. From my communication with Amazon shoppers like you, and the Consumer Relations folks at Insinkerator, it appears that current models have been redesigned to hopefully eliminate the problems I had. It also appears from those same communications that Insinkerator is going beyond the warranty period to replace some consumers' units when they discover this problem. Because of that I have upgraded my rating to a neutral 3-stars and modified my review somewhat. (In all fairness maybe I should retract it because of the design update. Have to give that some thought.) If you have problems with an existing unit, I also would encourage you to contact Insinkerator support to see what they can do for you. They're very good in my experience when your product is in warranty. I've heard from several folks that Insinkerator has replaced their unit outside of warranty too when they had this problem. Obviously there is some limit to what they will be willing to do, but the call is free. So if you've found this review because of a problem with your existing unit, your first step should be to call Insinkerator at 800-558-5712 and give them a chance to make it right. Post here with your experiences.(Original Review) This Insinkerator product suffers from a couple of design flaws. Like many here I found a puddle of water under my unit about two years after installing it. Checked into buying a new unit, but at $200 I wasn't going to give in easily. After reading other folks' experience with the unit I opened mine up and found the obvious source of the leak. There is a 1/4" plastic vent hose than helps handle the return hot water after you release the faucet handle. Since it's a non-pressurized unit, all water in the line up to faucet gets returned to the tank after you release the faucet handle. This hose, combined with a plastic overflow tank handles the water return. The root cause of the leaking problem is the type of tubing that was used for this one part. In the hot water heater it sits at near 200F, 24/7/365, and it can't handle the heat. Mine had turned a dark brown to nearly black color and had completely failed where the hose was routed right along the stainless steel tank. Every time we used the heater the return water ended up in our cabinet. Because of this one piece, customers everywhere are replacing their tanks prematurely. It can be fixed if you are handy. Please note that any modification of your unit will void the warranty, and rightfully so. If your unit is under warranty you should call Insinkerator at 800-558-5712 and have them replace it. If you buy a new unit, don't mess with it -- it's under warranty. Even if it's out of warranty, give them a call -- there's a good chance they'll do right by you. If you do try and repair it, know that you are on your own. Insinkerator strongly advises against any owner-initiated component repair. What I have done has been untested by Insinkerator and they have implemented their own fix in the current product design. Anything that happens during or after any repair you make will be your responsibility. And remember, nothing lasts forever.
HOW TO REPAIR: Basically you have to replace the hose with the right kind, and fortunately it's pretty easy. I recommend silicone tubing (rated to 500F), and you'll need some with 1/8" or 3/16" inside diameter. I bought some from an Amazon seller, 1/8" ID and 3/8" OD with thick 1/8" walls. (Edit: The original tubing is 3/16" ID but I went with 1/8 for a good snug fit. 3/16" ID tubing will also work quite well, and is what I would recommend at this point if you can find it.) Search on Amazon and you'll find what I'm talking about. Unfortunately it's only sold in 10' or longer lengths, and you need less than a foot. If you can find it locally, all the better. For good measure get a couple of small plastic zip ties (cable ties) or the proper sized spring clamp to secure the new tubing.
1) Unplug, drain, and remove the tank. After unplugging the power cord, run water thru the unit till cold water flows out the faucet. Then place a large bowl (1-gallon capacity minimum) under the tank, unscrew the drain screw, and let the tank drain into the bowl. If you can easily shut off the water supply do it now, but it is not necessary as long as no one uses the faucet when you are working on the tank. While draining, remove the three tubes from the top of the tank. One has a spring loaded clip you need to depress to remove the tube and the other two are silicone and plastic tubes that just pull off (might vary a bit based on the age of your unit). Loosen the mounting screws, and when the tank has drained, remove it from your cabinet and find a water resistant place to work on it.
2) Disassemble the tank. Really easy -- there is a small screw on the top that holds the two sides of the plastic shell together ... remove it. The two sides of the shell pull apart fairly easily but you might need to muscle it a bit. Once you get them apart, remove them from the unit and place aside. Then remove the temperature dial and put it aside. At this point you will have the guts of the unit with the steel tank encased in a dense styrofoam shell. Take a minute to examine the way it's put together (pictures wouldn't hurt either). You'll most probably easily pick out the problem part -- it will probably be very dark and brittle, and one end will be attached to the side of the water inlet port. Cut the hose somewhere before the metal (maybe plastic on yours) water inlet port it attaches to, and you will then be able to remove the upper styrofoam shell. After that you will see where the other end of the defective hose goes -- the bottom of the plastic overflow tank. You will need to cut the old zip ties (or maybe spring clamps) at each end of the hose to fully remove the old hose.
3) Inspect and dry the full unit. You may want at this point to remove the other styro shell piece and completely dry everything. At this point I discovered that the leaking water has badly rusted several of the screws holding the two pieces of the stainless tank together. IMHO they should have used stainless steel screws. I wasn't sure whether or not the rust has led to any leak in the tank itself, so I disassembled the stainless tank (fun to do with rusted screws I'll tell you). Mine took a T-10 Torx driver for the screws, and I eventually got them all out. A trip to the hardware store got me some #6 x 3/4" stainless machine screws and lock nuts. If you see anything else besides the hose that could be a problem, you'll need to deal with it for a complete repair.
4) Reassemble the unit, installing the new hose as you go. Put the tank back in the bottom styro shell. Attach one end of the silicone hose to the plastic overflow tank and secure with a zip tie cutting off the excess tie. Put the plastic tank back in the upper styro shell and slide the two back onto the top of the stainless tank. The plastic tank lines up with the silicone hose to the front of the unit. You'll route the hose along the tank flange to the right of the unit just like the old hose was. Once the shell is as far down as it goes, route the hose along the side of the styro shell following the groove for the old hose (not a perfect fit, but that's OK) and then over the top to the water inlet port. Hold it in place and see where you need to cut the silicone hose to fit the port without excess slack in the hose. Then cut the hose, attach it to the port and secure with a zip tie. Replace the thin upper piece of styro over the top of it all and reassemble it all into the plastic shell. Take your time and work the two halves together, making sure to get the power cord grommet correctly into the cutout in the shell. Get the bottom together first then work your way up. Pay attention to the new hose, keeping it tucked in behind the side of the front half of the shell (don't let it end up stuffed behind the back half of the shell. When done properly the shell will snap together nicely, and you may note a slight bulge where the new hose is if you used the thicker silicone tubing like me -- that's OK. Put the small screw back into the top the shell, and reinsert the drain screw.
5) Reinstall and test tank. Just reverse the removal steps. Open the faucet until water flows before plugging the tank in. Then use the faucet normally, checking regularly for any leaks. Mine has been leak free for two weeks, and should last for years now.
That's it, and it's probably easier than it sounds. For a grand total of less than $25 (with nine feet of hose left over) I have a fully functional tank again. The rest of the unit is very well made. The tank iteslf is built like a ... well, a tank, so I expect it to last years. Good luck with your home repair efforts if you try.
UPDATE 9/13/2010: A couple months now and still no leaks. I've been corresponding with another owner who ended up getting a replacement from Insinkerator. He sent me pics (thanks Jay!) that show they have changed the design of this particular tube that has been causing so many problems. The new design uses a different type of plastic for the tubing and avoids routing it along the steel hot water tank. They also seemed to have added a different type of gasket between the two tank halves. From what I saw, new units with this design won't suffer the same problem I described above, but how to tell whether any one new unit purchased at retail will have this fix incorporated??

Click Here to see more reviews about: InSinkErator SST-FLTR 2/3-Gallon Stainless Tank and Filtration System

The InSinkErator Stainless Steel Tank and Filtration System (SST-FLTR) saves time in the kitchen, delivering 200-degree-Fahrenheit near-boiling water from its compact 2/3-gallon tank. The tank delivers unmatched performance with its many features and benefits. The durable stainless steel construction means longer life, the adjustable thermostat gives you a water temperature that can be adjusted to your preference, the thermal protection system means the tank won't overheat and finally, dry start protection and tool free plumbing connections lead to worry free installation.
Included Filtration System Provides Better-Tasting WaterThe SST-FLTR includes InSinkErator's F-201 filtration system, the only water filtration system designed specifically for instant hot water dispensers. The filtration system reduces chlorine taste and odor for clean, fresh tasting water.
Quick-connect plumbing fittings make installation a snap and the sanitary quick-change filter cartridge is replaced in only seconds! This system is ideal for use virtually anywhere filtered water is needed, such as with ice makers and refrigerators.
Hundreds of Uses In Your HomeConsider how often you heat water in the kitchen. When you do, you'll realize just how useful the SST-FLTR will be. With 200-degree-Fahrenheit F near-boiling water available at your fingertips, you'll get more done in less time. Instead of waiting for water to heat, you can finish countless kitchen tasks in seconds and relax or get back to your guests.
An InSinkErator hot water dispenser does more than provide filtered hot water for preparing instant foods and beverages, it is also an incredible kitchen appliance. Use it to loosen stubborn jar lids, prepare pasta, warm baby food, clean crusty pans, cream butter, melt chocolate, remove fruit skins for pies, clean cheese graters, warm ice cream scoops, and warm pancake syrup. These are just a few examples of the many uses of an instant hot water dispenser.
Hot Water Instantly, How Does That Work?The SST-FLTR is so easy to use, you won't know how you lived without it. By activating your InSinkErator hot water dispenser's handle (dispensers sold separately), you'll send cool tap water into the tank. This water will displace the tanks' near-boiling water, which will flow out of the hot water dispenser's spout.
Water will be heated anywhere from 160 to 200 degrees, depending on the setting you choose, and it will flow into the tank's expansion chamber where it will be ready for later use. Release the handle, and the SST-FLTR's valve will close automatically, so hot water will stop flowing.
Easy to Install!The InSinkErator SST-FLTR features unique tool-free connections and a dry-start protection system for easy installation. It also features an adjustable temperature gauge, so you can adjust the water to your liking. Once connected to an InSinkErator hot water dispenser faucet (sold separately), this compact 2/3-gallon tank will give you instant access to filtered hot water--up to 60 cups an hour!
An Environmentally Friendly ChoiceHeating water with the SST-FLTR consumes less energy than a 40-watt light bulb that's left on for 24 hours and costs just pennies a day to operate. And because hot water is dispensed on demand, you only use the amount of water you need. This helps reduce water waste.
We Come To You Parts and Labor WarrantyThe SST-FLTR is backed by an exclusive three-year We Come to You In-Home Service Warranty. If you ever have a problem with your instant hot water dispenser system, an authorized InSinkErator service representative will come to your home and fix it, at no charge to you.
Note: Using other manufacturers' components with InSinkErator faucets or tanks voids all InSinkErator warranties.
What's in the BoxInSinkErator SST-FLTR Stainless Steel Tank and Filtration System.


Buy NowGet 52% OFF

Buy cheap InSinkErator SST-FLTR 2/3-Gallon Stainless Tank and Filtration System now.

3/22/2011

Rheem RHG PRO40-40F Pro Series Natural Gas Water Heater, 40 Gallon Review

Rheem RHG PRO40-40F Pro Series Natural Gas Water Heater, 40 Gallon
Average Reviews:

(More customer reviews)
I went out of my way to get this water heater due to the local supplier would not sell me one unless he installed it.It arrived in perfect condition or so I thought . I installed it with no problems at all. I turned on the water and it shot out the top of the Anode cap. Due to the suspended weight of the anode the forces caused the anode cap to crack during shipping. It should not have been installed before shiiping!! I e-mailed Rhhem twice and received NO reply. I called warranty service and got a very rude southern women who told me the anode is not covered under any warranty and i would have to buy it .Can you believe that? I refused so i ordered one from "Fiery Chill" on line for $21 shipped to the house. Rheem's cost for this part is about $5-6 and they refused to send me one Unbelievable!! The tank is a good product heats up in a flash,but Rheem is a terrible company as far as I am concerned . What if you have a real problem? The only difference between the 6yr tank and the 8yr tank is the anode Diameter . Buy the cheaper tank and buy the .900" anode you will save some money!!! Amazon is great they refunded the cost of the anode even though they didn't have to . Great company!!!!

Click Here to see more reviews about: Rheem RHG PRO40-40F Pro Series Natural Gas Water Heater, 40 Gallon

40 Gallons Flammable Vapor Ignition Resistant Natural Gas Professional Series Water Heater 8-year WarrantyFeatures:8-Year Limited Tank and Parts Warranty with a Professional Installation.One-of-a-kind air/fuel shut-off device offersdouble protectionMaintenance free . no filter to cleanStandard replacement partsLow NOx design for low nitrous oxide emissionsEverKleen™ patented system fights sediment build-upReduces fuel costsProvides more hot waterNo matches requiredMore hot water at low operating cost High Altitude CompliantAll models are certified for applications up to 6,000 feet above sea levelPatented magnesium anode rod design incorporates a special resistor that protects the tank from rustBrass drain valve and temperature and pressure relief valve are includedMeets or exceeds National Appliance Energy Conservation Act (NAECA) requirementsSpecifications:Type -- TallTank Capacity -- 40 gallonsGas Input BTU/hr.-- 40Recovery in G.P.H at 90° Rise -- 40.4Energy Factor -- 0.62Shipping Weight - 135 lbs.Average Annual Operation Costs -- $220

Buy NowGet 16% OFF

Buy cheap Rheem RHG PRO40-40F Pro Series Natural Gas Water Heater, 40 Gallon now.